-
1 утоплен
•The batteries of light are recessed in the factory ceiling.
•The thermometer is fitted flush with the wall.
•The field windings are completely embedded (or buried) in iron.
Русско-английский научно-технический словарь переводчика > утоплен
-
2 электродвигатель
electric motor
(рис. 90)
- азимутальной коррекции (гироагрегата гик) — azimuth torque motor
-, асинхронный — asynchronous motor
-, гистерезисный — hysteresis motor
синхронный эл. дв. без выступающих полюсов н возбуждения пост. током. — a synchronous motor without salient poles or direct-current excitation.
- горизонтальной коррекции (эдгк) — leveling torque motor
-, индукционный — induction motor
эл. двиг. переменного тока, у которого основная (статорная) обмотка соединяется с источником питания и взаимодействует с обмоткой ротора (обычно типа "беличье колесо") — an alternating-current motor in which the primary winding (usually the stator) is connected to the power source and induces а current into a polyphase secondary or squirred-cage secondary winding (usually the rotor).
-, исполнительный — servomotor, servo electric motor
эл. двиг. в системе сервоуправлания. обороты двигателя регулируются коррекционным эл. сигналом, усиливаемым и подаваемым в цепь электродвигателя. — а motor used in а servo system. its rotation or speed (or both) are controlled by a corrective electric signal that has been amplified and fed into the motor circuit.
-, компаундный — compound-wound motor
эл. двиг. постоянного тока с двумя отдельными обмотками возбуждения. одна обмотка включена параллельно, a другая последовательно обмотке якоря. — а d-c motor having two separate field windings. one, usually the predominant field, is connected in parallel with the armature circuit and the other is connected in series.
-, коррекционный (гироскопа) — erection torque motor /torquer/
-, сериесный — series motor
эл. двиг. с обмоткой возбуждения, включенной последовательно с обмоткой якоря. — а motor in which the field and armature circuits are connected in series.
-, синхронный — synchronous motor
an induction motor which runs at synchronous speed.
- следящей системы — servomotor
- следящей системы (рамки гироплатформы) — gimbal servomotor
-, шумовой — shunt-wound motor
эл. двиг. постоянного тока с обмоткой возбуждения, включенной параллельно обмотке якоря. — а direct-current motor in which the field circuit and armature circuit are connected in parallel.Русско-английский сборник авиационно-технических терминов > электродвигатель
-
3 обмотка
обмотка
Совокупность витков, образующих электрическую цепь с целью получения одного из напряжений трансформатора.
Примечание — Для трехфазного трансформатора под «обмоткой» подразумевается совокупность соединяемых между собой обмоток одного напряжения всех фаз, см. 3.3.3
(МЭС 421-03-01).
[ ГОСТ 30830-2002]
обмотка
Ндп. намотка
По ГОСТ 18311-80
[ ГОСТ 20718-75]
обмотка
Изолированный проводник, уложенный в специфическом порядке, предназначенный для возбуждения магнитного поля при протекании по нему электрического тока
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
обмотка
-
[IEV number 151-13-17]EN
winding
the assembly of turns forming an electric circuit associated with one of the voltages assigned to the transformer or to the reactor
NOTE – For a polyphase transformer or polyphase reactor, the "winding" is the combination of the phase windings
[IEV number 421-03-01]
winding
assembly of interconnected turns and/or coils intended for common operation
NOTE – A winding is provided with terminals and is intended to produce a magnetic field when carrying electric currents or to produce voltages between appropriate points when placed in a time-varying magnetic field or moved through a magnetic field.
[IEV number 151-13-17]FR
enroulement
ensemble des spires formant un circuit électrique associé à l'une des tensions pour lesquelles le transformateur ou la bobine d'inductance ont été établis
NOTE – Pour un transformateur polyphasé ou pour une bobine d'inductance polyphasée, l"enroulement" est l'ensemble des enroulements de phase.
[IEV number 421-03-01]
enroulement, m
ensemble de spires ou de bobines interconnectées et destinées à fonctionner conjointement
NOTE – Un enroulement est muni de bornes et est destiné à produire un champ magnétique lorsqu’il est parcouru par des courants électriques ou à produire des tensions électriques entre des points appropriés lorsqu’il est placé dans un champ magnétique variable dans le temps ou déplacé dans un champ magnétique.
[IEV number 151-13-17]Недопустимые, нерекомендуемые
Тематики
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > обмотка
-
4 обмотка
обмотка
Совокупность витков, образующих электрическую цепь с целью получения одного из напряжений трансформатора.
Примечание — Для трехфазного трансформатора под «обмоткой» подразумевается совокупность соединяемых между собой обмоток одного напряжения всех фаз, см. 3.3.3
(МЭС 421-03-01).
[ ГОСТ 30830-2002]
обмотка
Ндп. намотка
По ГОСТ 18311-80
[ ГОСТ 20718-75]
обмотка
Изолированный проводник, уложенный в специфическом порядке, предназначенный для возбуждения магнитного поля при протекании по нему электрического тока
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
обмотка
-
[IEV number 151-13-17]EN
winding
the assembly of turns forming an electric circuit associated with one of the voltages assigned to the transformer or to the reactor
NOTE – For a polyphase transformer or polyphase reactor, the "winding" is the combination of the phase windings
[IEV number 421-03-01]
winding
assembly of interconnected turns and/or coils intended for common operation
NOTE – A winding is provided with terminals and is intended to produce a magnetic field when carrying electric currents or to produce voltages between appropriate points when placed in a time-varying magnetic field or moved through a magnetic field.
[IEV number 151-13-17]FR
enroulement
ensemble des spires formant un circuit électrique associé à l'une des tensions pour lesquelles le transformateur ou la bobine d'inductance ont été établis
NOTE – Pour un transformateur polyphasé ou pour une bobine d'inductance polyphasée, l"enroulement" est l'ensemble des enroulements de phase.
[IEV number 421-03-01]
enroulement, m
ensemble de spires ou de bobines interconnectées et destinées à fonctionner conjointement
NOTE – Un enroulement est muni de bornes et est destiné à produire un champ magnétique lorsqu’il est parcouru par des courants électriques ou à produire des tensions électriques entre des points appropriés lorsqu’il est placé dans un champ magnétique variable dans le temps ou déplacé dans un champ magnétique.
[IEV number 151-13-17]Недопустимые, нерекомендуемые
Тематики
Классификация
>>>EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > обмотка
-
5 обмотка
обмотка
Совокупность витков, образующих электрическую цепь с целью получения одного из напряжений трансформатора.
Примечание — Для трехфазного трансформатора под «обмоткой» подразумевается совокупность соединяемых между собой обмоток одного напряжения всех фаз, см. 3.3.3
(МЭС 421-03-01).
[ ГОСТ 30830-2002]
обмотка
Ндп. намотка
По ГОСТ 18311-80
[ ГОСТ 20718-75]
обмотка
Изолированный проводник, уложенный в специфическом порядке, предназначенный для возбуждения магнитного поля при протекании по нему электрического тока
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
обмотка
-
[IEV number 151-13-17]EN
winding
the assembly of turns forming an electric circuit associated with one of the voltages assigned to the transformer or to the reactor
NOTE – For a polyphase transformer or polyphase reactor, the "winding" is the combination of the phase windings
[IEV number 421-03-01]
winding
assembly of interconnected turns and/or coils intended for common operation
NOTE – A winding is provided with terminals and is intended to produce a magnetic field when carrying electric currents or to produce voltages between appropriate points when placed in a time-varying magnetic field or moved through a magnetic field.
[IEV number 151-13-17]FR
enroulement
ensemble des spires formant un circuit électrique associé à l'une des tensions pour lesquelles le transformateur ou la bobine d'inductance ont été établis
NOTE – Pour un transformateur polyphasé ou pour une bobine d'inductance polyphasée, l"enroulement" est l'ensemble des enroulements de phase.
[IEV number 421-03-01]
enroulement, m
ensemble de spires ou de bobines interconnectées et destinées à fonctionner conjointement
NOTE – Un enroulement est muni de bornes et est destiné à produire un champ magnétique lorsqu’il est parcouru par des courants électriques ou à produire des tensions électriques entre des points appropriés lorsqu’il est placé dans un champ magnétique variable dans le temps ou déplacé dans un champ magnétique.
[IEV number 151-13-17]Недопустимые, нерекомендуемые
Тематики
Классификация
>>>EN
DE
FR
20. Обмотка
Ндп. Намотка
Е. Winding
F. Enroulement
Источник: ГОСТ 20718-75: Катушки индуктивности аппаратуры связи. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > обмотка
-
6 подавать сигнал
Подавать сигнал-- The amplified error signal is fed to the reference field windings of the amplidyne generator by terminals 40, 41, and 42.Русско-английский научно-технический словарь переводчика > подавать сигнал
-
7 коэффициент
coefficient (coeff.), factor
безразмерное число, в основном отношение к-п. величин, характеризующих заданные условия. — а number indicating the amount of some change under certain specified сoпditions, often expressed as a ratio.
- безопасности — factor of safety
число, равное отношению расчетной нагрузки к эксплуатационной. расчетная нагрузка - произведение эксплуатационной нагрузки на коэффициент безопасности. — а number indicating the ratio between the ultimate load and limit load (maximum load expected in service). ultimate load is limit load multiplied by factor of safety.
- восстановления давления — pressure recovery factor
- двухконтурности (дтрд) — bypass ratio
- загрузки пассажирами, безубыточный — passenger break-even load factor
- запаса длины впп — field length factor
- запаса длины летной полосы — field length factor
- запаса длины летной полосы в направлении взлета — takeoff field length factor
- запаса длины летной полосы в направлении посадки — landing field length factor
- запаса длины летной полосы при всех работающих двигателей — field length factor for all-engines-operating сase
- запаса длины летной полосы при одном отказавшем двигателе — field length factor for one-engine-inoperative ease
- запаса прочности — reserve factor
отношение фактической прочности конструкции к минимально-потребной в данных условиях. — а ratio of the actual strength of the structure to the minimum required to specific condition.
- заполнения (в вычислительном уст-ве) — duty factor in computer, the ratio of active time to total time.
- заполнения (воздушного) винта — propeller solidity ratio
отношение суммарной площади всех лопастей винта к сметаемой ими площади. — the ratio of the total projected blade area to the area of the projected outline of the propeller disc.
- заполнения несущего винта (вертолета) — rotor solidity ratio solidity of rotor is a ratio of the total blade area to the disc area.
- лобового сопротивления (сх) — drag coefficient (cd)
коэффициент, характеризующий лобовое сопротивление рассматриваемого аэродинамического профиля. — а coefficient representing the drag on а given airfoil.
- маневренной перегрузки — maneuvering load factor
- момента крена — rolling-moment coefficient
- момента рыскания — yawing-moment coefficient
- момента тангажа — pitching-moment coefficient
- мощности — power factor
- мощности (воздушного винта) — activity factor
- мощности лопасти (возд. винта) — blade activity factor
безразмерная функция поверхности лопасти, характеризующая способность лопасти использовать прикладываемую мощность. — а non-dimensional function of the blade surface used to express capacity of a blade for absorbing power.
- несущей поверхности (покрытия аэродрома), калифорнийский — californian bearing ratio (с.в.r.)
-, относительный (воздушного винта) — figure of merit
- перегрузки (n) — load factor (n)
число, показывающее, во сколько раз нагрузки, действующие на самолет (или его отдельные части), превышает нагрузки в равномерном горизонтальном полете или нагрузки от веса при стоянке. — the ratio to the weight of an aircraft of а specified exterпаl load. such load may arise from aerodynamic forces, gravity, ground or water reaction, or from combinations of these forces.
- перегрузки, максимальный эксплуатационный — limit load factor
- перегрузки, (полетный) — flight load factor
отношение составляющей аэродинамической нагрузки (действующей перпендикулярно продольной оси ла) к весу ла. — the ratio of the aerodynamic force component (acting normal to the assumed longitudiпа1 axis of the airplane) to the weight of the airplane.
- перегрузки (полетной), отрицательный — negative load factor
- перегрузки (полетной), положительный — positive load factor
в данном случае аэродинамичеекая сила воздействует на ла снизу вверх. — in positive load factor the aerodynamic force acts upward with respect to the airplane.
- перегрузки при маневре — maneuvering load factor
- перегрузки при маневре, максимальный эксплуатационный — limit maneuvering load factor
- перегрузки, расчетный — ultimate load factor
- передачи (коэффициент передаточного числа в системе управления ла) — gain
- подъемной силы (су) безразмерная величина, определяемая по формуле. — lift coefficient (cl) а coefficient representing the lift of а given airfoil or other body. the lift coefficient is obtained ьу dividing the lift by the free-stream dynamic pressure and by the representative area under consideration.
- полезного действия (кпд) — efficiency (n)
the ratio of the useful output of the quantity to its total input.
- полезного действия, общий — overall efficiency
- полезного действия,тепловой — thermal efficiency
-, поправочный — correction factor
например, для учета влияния погодных (сезонных) условий (температура наружного воздуха, атмосферные осадки, обледенение) на характеристики тормозного участка впп в пределах установленных эксплуатационных ограничений. — the correction factors must account for the particular surface characteristics of the stopway and the variations in these characteristics with seasonal weather conditions (such as temperature, rain, snow, and ice) within the established operational limits.
- предельной перегрузки — ultimate load factor
- преобразования (в преобразователе) — conversion efficiency ratio of dc output power to ас input power.
- профильного сопротивления — profile drag coefficient
- прочности грунта, калифорнийский — californian bearing ratio (c.b.r.)
(к. несущей способности покрытия аэродрома, впп) — c.b.r. is used to measure subsoil strength of the runways and airfields.
- связи (эл.) — coupling coefficient
- сжимаемости — coefficient of compressibility
относительное уменьшение объема газа при повышении давления в изотермическом процессе. — the relative decrease of the volume of а gaseous system with increasing pressure in an isothermal process.
- совершенства (воздушного винта) — figure of merit
- сопротивления (лобовой, сx) — drag coefficient (cd)
- сопротивления (сx) груза на внешней подвеске (вертолета) — drag coefficient (cd) representing а drag caused by an externally-slung load
- стоячей волны — standing wave ratio (swr)
- схождения карты — chart convergence factor (ccf)
- сцепления (между шиной колеса и поверхностью впп) — coefficient of friction
-, сцепления (между шиной и впп при торможении) — braking coefficient of friction
- трансформации (в трансформаторе) — transformation ratio compensation windings are used to correct for variations in the resolvers transformation ratio.
- трения — coefficient of friction
- трения торможения — braking coefficient of friction
коэффициент трения между шиной и поверхностью взлетно-посадочной полосы при торможении самолета. — braking coefficient of friction between the aircraft wheel tires and runway (surface).
- трения торможения, осредненный приведенный — (mean) corrected braking coefficient of friction
- тяги (воздушного винта) — thrust coefficient (ст)
- усиления (эл.) — amplification factor
the ratio of output magnitude to input magnitude.
- усиления антенны — antenna gain
- усиления (передаточное число в системе управления) — gain
- усиления, самонастраивающийся (системы управления) — adaptive gain
- утечки — leakage factor
- шарнирного момента — hinge moment factor
- шарнирного момента от порыва ветра на земле, предельный — limit hinge moment factor (к) for ground gusts
в отношении элеронов и рулей высоты, коэффициент имеет положительный знак, если момент, воздействующий на поверхность управления, вызывает ее опускание. — for ailerons and elevators, а positive value of к indicates а moment tending to depress the surface, and а negative value of к - to raise the surface.
- шума — noise factor
для данной полосы частот, отношение суммарной величины помех на выходе к величине помехи на входе. — for а given bandwidth, the ratio оf total noise at the output, to the noise at the input.
- эксплуатационной маневренной перегрузки (максимальный), или эксплуатационной перегрузки при маневрировании (отрицательный или попожительный) — (negative, positive) limit maneuvering load factor rotorcraft must be designed for positive limit maneuvering load factor of 3.5 and negafive limit maneuvering load factor of 1.0.Русско-английский сборник авиационно-технических терминов > коэффициент
-
8 обмотка
winding
(процесс наматывания обмотки)
- (электрическая) — winding
-, бифилярная — bifilar winding
- возбуждения (генератора, мотора) (рис. 90) — field winding
- возбуждения (трансформатоpa ckt) — exitation winding (of resolver control transformer)
-, вторичная (трасформатора) — secondary winding
-, коммутирующая (генератоpa) — commutating wiring
-, компенсирующая (генератоpa) — compensating winding
- моментного датчика (гироскопа или акселерометра) — torquer coils
-, первичная (трансформатора) — primary winding
-, смещения (в усилителе) — bias winding
-, сериесная — series winding
- соединенная "звездой" — y-connected windings
-, шунтовая — shunt winding
- якоря (рис. 90) — armature winding
замыкание о. — shorting in the winding
напряжение на о. — voltage across /on/ winding
обрыв 0. — break in the winding
секция 0. якоря — armature winding coilРусско-английский сборник авиационно-технических терминов > обмотка
См. также в других словарях:
field current — noun : the current supplied to the field windings of a generator or motor to establish the magnetic field for its operation * * * Elect. the current in a field winding. Also called exciting current … Useful english dictionary
Field coil — A field coil is a component of an electro magnetic machine, typically a rotating electrical machine such as a motor or generator. A current carrying coil is used to generate a magnetic field. Magnetic fields require a continuous circuit, thus… … Wikipedia
Magnetic field — This article is about a scientific description of the magnetic influence of an electric current or magnetic material. For the physics of magnetic materials, see magnetism. For information about objects that create magnetic fields, see magnet. For … Wikipedia
clutch field — A clutch part on an air condition compressor, consisting of hundreds of windings of wire, that creates a magnetic field when current is applied, pulling in the armature to engage the clutch … Dictionary of automotive terms
Mongol conquest of the Song Dynasty — Southern Song before Mongol World conquests Date 1235 1279 Locati … Wikipedia
polarizing — The process of sending a quick surge of current through the field windings of the generator in a direction that will cause the pole shoes to assume the correct polarity. This will insure that the generator will cause current to flow in the same… … Dictionary of automotive terms
Electric motor — For other kinds of motors, see motor (disambiguation). For a railroad electric engine, see electric locomotive. Various electric motors. A 9 volt PP3 transistor battery is in the center foreground for size comparison. An electric motor converts… … Wikipedia
electric generator — ▪ instrument Introduction also called dynamo, any machine that converts mechanical energy to electricity for transmission and distribution over power lines to domestic, commercial, and industrial customers. Generators also produce the… … Universalium
Electrical machine — is a device that convert either mechanical energy to electrical energy or vice versa, and change AC voltage from one level to another level.Electrical machines are divided into three parts:GeneratorGenerator is the device that converts mechanical … Wikipedia
Ward Leonard control — Ward Leonard Control, also known as the Ward Leonard Drive System, was a widely used DC motor speed control system introduced by Harry Ward Leonard in 1891. In early 1900s, the control system of Ward Leonard was adopted by the U.S Navy and also… … Wikipedia
Squirrel-cage rotor — A squirrel cage rotor is the rotating part often used in an AC induction motor. An electric motor with a squirrel cage rotor is sometimes called a squirrel cage motor. In overall shape it is a cylinder mounted on a shaft. Internally it contains… … Wikipedia